{"title":"Stopwatch","description":"","products":[{"product_id":"seiko-aquatic-swimming-sports-300-lap-waterproof-stopwatch-svas009","title":"SEIKO Swimming Master SVAS009 Stopwatch, 300-Lap Memory, Stroke Rate, 10 Bar Water Resistant","description":"\u003ch2\u003eProduct Description\u003c\/h2\u003e\n\u003cp\u003eThe SEIKO SVAS009 is the Swimming Master (スイミングマスター), a digital stopwatch from Seiko Watch Corporation of Tokyo, Japan, built on Seiko's stopwatch caliber S141. Seiko's Swimming Master series page presents it as a 10 bar water resistant model for swimming, rowing and other sports around water. It times in 1\/100 second units on a 10-hour counter and shows three times at once on a large three-row display: the split time, the lap time, and either the total elapsed time or the lap in progress (Seiko calls the latter the running lap).\u003c\/p\u003e\n\u003cp\u003eLap and split times go into memory automatically, up to 300 of them. Seiko calls the system \"dual memory\". In single memory mode, the factory setting, the stopwatch keeps the laps of one timing run and clears them when the next run starts; resetting alone does not erase them. In block memory mode, each run from start to stop or reset is kept as a numbered block together with its start date and time, up to 100 blocks, and earlier blocks are not erased. Seiko's English manual describes block memory mode as useful for saving records or comparing data. The fastest lap of each block can be recalled. Stored times can be called up while the stopwatch is still timing, and a bar indicator on the display shows how much of the memory is in use.\u003c\/p\u003e\n\u003cp\u003eThe stroke rate function, which Seiko calls the pitch function and which is marked STROKE BASE 3 on the dial, turns the time taken by three strokes into strokes per minute. Seiko's manual gives the pull of a rowing oar as its example. The last 9 results are kept. In its time\/calendar display the SVAS009 shows the time and a full auto calendar (year, month and date), and an ID number from 01 to 99 can be set, which Seiko says helps keep different users' data apart. Seiko lists the body as antibacterial; its manual adds that the antibacterial effect declines over time and differs with the conditions of use.\u003c\/p\u003e\n\u003cp\u003eSeiko's Swimming Master feature page lists two silicone cases made for this model only: SVAZ011 in blue and SVAZ013 in yellow. They are sold separately.\u003c\/p\u003e\n\u003ch2\u003eProduct Specification\u003c\/h2\u003e\n\u003cp\u003e\n- Maker: Seiko Watch Corporation, Tokyo, Japan\u003cbr\u003e\n- Product name: SEIKO Swimming Master stopwatch\u003cbr\u003e\n- Model: SVAS009\u003cbr\u003e\n- Caliber: S141\u003cbr\u003e\n- JAN: 4954628451392\u003cbr\u003e\n- Movement: battery-powered quartz\u003cbr\u003e\n- Accuracy: within ±15 seconds per month (±0.0006%) at normal temperatures of 5 to 35 °C\u003cbr\u003e\n- Stopwatch: 1\/100 second units, 10-hour counter (the manual gives the maximum as 9 h 59 min 59.99 s)\u003cbr\u003e\n- Display: three rows showing split time, lap time, and total elapsed time or running lap time\u003cbr\u003e\n- Lap\/split memory: up to 300 times, recallable during and after timing; single memory mode (factory setting) or block memory mode (up to 100 blocks, each with its start date and time; fastest-lap recall per block). In block mode each block also uses memory for its number and start time, so the memory can fill before 300 laps are stored. Once the memory is full, further laps are still timed and displayed but are not stored\u003cbr\u003e\n- Lap\/split count display: up to 999\u003cbr\u003e\n- Memory indicator: 10-segment bar, 30 entries per segment\u003cbr\u003e\n- Stroke rate (pitch) function: measures the time of three strokes; range 10 to 180 strokes per minute (measuring time 1 to 18 seconds); last 9 results stored\u003cbr\u003e\n- Clock and calendar: 24-hour time; full auto calendar (year, month, date) from 2006 to 2055; ID number OFF or 01 to 99; display contrast adjustable in 10 levels\u003cbr\u003e\n- Water resistance: 10 bar (Seiko class: reinforced water resistance for everyday use; dial print \"WATER RESISTANT 10BAR\")\u003cbr\u003e\n- Case: plastic; an antibacterial agent is applied to the case surface (Seiko notes the effect declines over time and differs with the conditions of use)\u003cbr\u003e\n- Glass: Hardlex\u003cbr\u003e\n- Case thickness: 22.0 mm\u003cbr\u003e\n- Weight: 90.0 g\u003cbr\u003e\n- Strap: neck strap\u003cbr\u003e\n- Battery: lithium SB-T74 (listed as CR2430 in Seiko's Japanese manual), 1 piece; battery-end warning (\"BATT\" flashes)\u003cbr\u003e\n- Battery life: approx. 3 years, based on 3 hours of stopwatch use per day. The battery fitted at the factory is a monitor battery and may run out sooner\u003cbr\u003e\n- Operating temperature: -10 to +60 °C\u003cbr\u003e\n- Instruction manual: Seiko publishes the S141 manual on its website in Japanese and in English\u003cbr\u003e\n- Options (sold separately): Swimming Master silicone case SVAZ011 (blue) or SVAZ013 (yellow), made for the SVAS009 only\u003cbr\u003e\n- Sources: Seiko's SVAS009 product page, Seiko's Swimming Master series and feature pages, Seiko's water resistance care page, and the Seiko S141 instruction manual (Japanese and English editions)\n\u003c\/p\u003e\n\u003ch2\u003eUsage\u003c\/h2\u003e\n\u003cp\u003eSeiko names swimming, rowing and other water sports as the uses for this model. Seiko's manual labels the buttons A to D: A (START\/STOP) starts and stops timing; B (LAP\/SPLIT, RESET) takes a split and lap while timing and resets once the stopwatch is stopped; C (RECALL) calls up stored times; D (MODE) moves between the total-time stopwatch display, the running-lap stopwatch display, the stroke rate display and the time\/calendar display. Reset the stopwatch to zero before you start.\u003c\/p\u003e\n\u003cp\u003eRecalling times: press C. While the stopwatch is timing, stored times come up newest first; when it is stopped or reset, they come up oldest first. Holding C scrolls through them. To switch to block memory mode, reset the stopwatch, press D to the time\/calendar display, press B repeatedly until BLOCK appears with ON or OFF flashing, and hold A for 1.5 seconds until a long beep (ON is block memory, OFF is single memory). Changing the memory mode erases everything stored. To clear the memory, reset the stopwatch, press C, then hold B for 1.5 seconds or more; all data is erased at once; individual times or blocks cannot be deleted separately.\u003c\/p\u003e\n\u003cp\u003eStroke rate: press D to show the stroke rate display, press A to start the measurement, and press A again when the third stroke is complete. The display shows strokes per minute. Stopping within the first second, or not stopping within 18 seconds, shows \"Error\". Press C to recall the last 9 results; they cannot be recalled while a measurement is running.\u003c\/p\u003e\n\u003cp\u003eWater and care, as stated by Seiko: the 10 bar rating makes the stopwatch usable in rain and in sports where it gets splashed. Seiko's English manual adds: do not operate the buttons when the stopwatch is wet or in water; it is not for scuba diving; after use in sea water, rinse it in fresh water and dry it completely. Seiko's care guidance also says not to hold a watch directly under a running tap, because the water pressure can exceed its rating. Peel off any protective film or sticker on the case back before use. Keep it away from solvents, cosmetic sprays, detergents, adhesives and paints. Long exposure to direct sunlight can turn the display black, and long periods below -10 °C can make the digits change slowly and the timing drift slightly; both recover at normal temperature. Seiko recommends a check every 2 to 3 years, and gives the normal life of the liquid crystal panel as about 7 years.\u003c\/p\u003e\n\u003cp\u003eBattery: do not remove the battery yourself. Seiko asks for replacement by a Seiko dealer with a Seiko SB-T74 battery, and its Japanese manual asks for a water resistance test at the same time, which it says is especially needed for watches rated 10 bar or more. All stored data is erased when the battery is replaced.\u003c\/p\u003e","brand":"SEIKO","offers":[{"title":"Default Title","offer_id":43296548683939,"sku":"20230698","price":22000.0,"currency_code":"JPY","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0590\/1271\/0563\/products\/seiko-aquatic-swimming-sports-300-lap-waterproof-stopwatch-svas009-634436.jpg?v=1695256530"},{"product_id":"citizen-rhythm-stopwatch-l-8rda04-008-simple-cumulative-split-time-dual-timer","title":"CITIZEN RHYTHM Stopwatch L 8RDA04-008 Simple Cumulative Split Time Dual Timer","description":"\u003ch2\u003eProduct Description\u003c\/h2\u003e\n\u003cp\u003eThis versatile timekeeping device offers simple timekeeping, totalizing timekeeping, split timekeeping, and simultaneous 1st and 2nd place timekeeping. It is designed to cater to various timing needs, making it suitable for sports events, competitions, and other activities requiring precise time measurement.\u003c\/p\u003e\n\n\u003ch2\u003eProduct Specification\u003c\/h2\u003e\n\u003cp\u003e\n- Dimensions: 78mm x 60mm\u003cbr\u003e\n- Water Resistance: Not waterproof\u003cbr\u003e\n- Allergy Resistance: Not confirmed by the manufacturer; may not be suitable for allergy sufferers\u003cbr\u003e\n- Origin: China\n\u003c\/p\u003e\n\n\u003ch2\u003eAbout the Manufacturer\u003c\/h2\u003e\n\u003cp\u003eCITIZEN (Citizen Watch Co., Ltd.), founded in 1930, is a renowned manufacturer engaged in the businesses of watches, information and electronic equipment, health equipment, and industrial machinery. The company's founding business, the watch business, offers a wide range of products, from high-function, high-quality sports watches using radio-controlled clocks to astronomical clocks.\u003c\/p\u003e","brand":"CITIZEN","offers":[{"title":"Default Title","offer_id":45101491880099,"sku":"20244437","price":5800.0,"currency_code":"JPY","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0590\/1271\/0563\/files\/citizen-rhythm-stopwatch-l-8rda04-008-simple-cumulative-split-time-dual-timer-926650.jpg?v=1723851943"},{"product_id":"evernew-system-stopwatch-svas011egc302","title":"SEIKO System Stopwatch SVAS011 (EVERNEW EGC302), 300-Lap Block Memory, Connects to SVAZ017 Printer","description":"\u003ch2\u003eProduct Description\u003c\/h2\u003e\n\u003cp\u003eThe SVAS011 is Seiko's System Stopwatch (システムストップウオッチ), a digital stopwatch from Seiko Watch Corporation built on Seiko's stopwatch caliber S143. In Japan it is also sold by the Japanese sports-goods company EVERNEW under EVERNEW's item code EGC302; EVERNEW's product page states that it is made by Seiko. Seiko's stopwatch lineup describes the System Stopwatch series as a full-scale stopwatch widely used across track and field.\u003c\/p\u003e\n\u003cp\u003eIt times in 1\/100 second units on a 10-hour counter and covers simple timing, accumulated timing (stop and restart as many times as needed) and lap\/split timing. A large three-row display shows the split time, the lap time, and either the total elapsed time or the lap in progress at the same time, and the lap\/split count is shown up to 999.\u003c\/p\u003e\n\u003cp\u003eThe SVAS011 uses Seiko's block memory system. Each run from start to finish is stored as a numbered block together with its start date and time, without erasing earlier blocks. Up to 300 entries and up to 100 blocks can be stored. Stored times can be recalled while the stopwatch is still timing, the fastest lap of each block can be called up, and a bar indicator shows how much of the memory is in use. Because each block also uses memory for its block number and start time, the memory can fill before 300 lap or split times are stored. An ID number from 01 to 99 can be set so that the data of different users or units can be told apart.\u003c\/p\u003e\n\u003cp\u003eWith Seiko's System Printer SVAZ017 (sold separately; EVERNEW item code EGC303) connected with the connecting cord, times can be printed as they are taken, and stored data can be printed afterwards, either one chosen block or all blocks. Seiko also states that the auto-start time set on its printer-integrated stopwatch SVAS013 (sold separately) can be transferred to the SVAS011 with connection cord 7504500 (sold separately), so that timing at the start and at several checkpoints begins at the same preset time; Seiko names marathons and ekiden road relays as examples.\u003c\/p\u003e\n\u003cp\u003eWhen no timing is running, the SVAS011 can show the time and date with a full auto calendar (select it with the MODE button). Seiko lists the body as antibacterial; its manual adds that the antibacterial effect declines over time and that how long it lasts depends on the conditions of use.\u003c\/p\u003e\n\u003ch2\u003eProduct Specification\u003c\/h2\u003e\n\u003cp\u003e\n- Maker: Seiko Watch Corporation, Japan\u003cbr\u003e\n- Product name: SEIKO System Stopwatch\u003cbr\u003e\n- Model: SVAS011\u003cbr\u003e\n- EVERNEW item code: EGC302\u003cbr\u003e\n- Caliber: S143\u003cbr\u003e\n- Movement: battery-powered quartz\u003cbr\u003e\n- Accuracy: loss or gain of less than 15 seconds per month at normal temperatures of 5 to 35 deg C\u003cbr\u003e\n- Stopwatch: 1\/100 second units, 10-hour counter; simple, accumulated and lap\/split timing\u003cbr\u003e\n- Display: three rows showing split time, lap time, and total elapsed time or lap time in progress\u003cbr\u003e\n- Memory: block memory system, up to 300 entries and up to 100 blocks, each block with its start date and time; recall during and after timing; fastest-lap recall per block\u003cbr\u003e\n- Lap\/split count display: up to 999\u003cbr\u003e\n- Memory indicator: 10-segment bar, 30 entries per segment\u003cbr\u003e\n- Clock and calendar: 24-hour time, full auto calendar (year settable from 1999 to 2048); ID number OFF or 01 to 99; display contrast adjustable in 10 levels\u003cbr\u003e\n- Printing: with the Seiko System Printer SVAZ017 (sold separately), during timing or afterwards from memory\u003cbr\u003e\n- Water resistance: water resistant for everyday use (Seiko's class; the S143 manual gives 3 bar). This is a lower class than the 10 bar rating of Seiko's Swimming Master SVAS009\u003cbr\u003e\n- Case: plastic, antibacterial treatment (Seiko notes the effect declines over time)\u003cbr\u003e\n- Glass: Hardlex\u003cbr\u003e\n- Size: approx. 8 cm (length) x 6 cm (width) x 2.2 cm (thickness), as listed by EVERNEW; Seiko gives a case thickness of 22.0 mm\u003cbr\u003e\n- Weight: 88 g\u003cbr\u003e\n- Battery: lithium SB-T74 in Seiko's manual (listed as CR2430 by EVERNEW), 1 piece; battery-end warning (\"BATT\" flashes)\u003cbr\u003e\n- Battery life: approx. 3 years; it may be shorter if the stopwatch is used for more than 3 hours a day. The battery fitted at the factory is a monitor battery for checking the stopwatch and may run out sooner\u003cbr\u003e\n- Operating temperature: -10 to +60 deg C (Seiko gives 0 to +50 deg C as the desirable range of use)\u003cbr\u003e\n- Country of manufacture: Japan, as stated by EVERNEW\u003cbr\u003e\n- Instruction manual: Seiko publishes the Cal. S143 manual on its website in Japanese and in English\u003cbr\u003e\n- Options (sold separately): Seiko System Printer SVAZ017 (EVERNEW EGC303); thermal roll paper S-950 for the printer's standard holder (EVERNEW sells it as EGC143, a case of 10 boxes of 5 rolls)\u003cbr\u003e\n- Sources: Seiko's SVAS011 product page, Seiko's System Stopwatch, System Printer and printer-integrated stopwatch feature pages, the Seiko Cal. S143 instruction manual (English edition), the Seiko Cal. S149 (SVAS013) instruction manual for the auto-start transfer, and EVERNEW's EGC302 product page\n\u003c\/p\u003e\n\u003ch2\u003eUsage\u003c\/h2\u003e\n\u003cp\u003eSeiko's manual labels the buttons A to D: A (START\/STOP) starts and stops timing; B (LAP\/SPLIT, RESET) takes a lap and split while timing and resets once the stopwatch is stopped; C (RECALL) calls up stored times; D (MODE) moves between the total elapsed time display, the lap-in-progress display and the time\/calendar display.\u003c\/p\u003e\n\u003cp\u003eBasic timing: press A to start, A to stop and B to reset; the number of the next block is then shown. For accumulated timing, press A repeatedly to stop and restart, then B to reset. For laps and splits, press A to start, B at each lap, A at the finish and B to reset.\u003c\/p\u003e\n\u003cp\u003eRecalling times: press C. While the stopwatch is timing, stored times come up newest first; when it is stopped or reset, they come up oldest first, starting from block 1. Holding C scrolls through them. To clear the memory, reset the stopwatch, press C, then hold B for more than 1.5 seconds. All stored data is erased at once; single blocks cannot be deleted one by one.\u003c\/p\u003e\n\u003cp\u003ePrinting (printer sold separately): connect the stopwatch and the printer with the cord and switch the printer on; times are then printed as they are taken. To print stored data, connect the printer and switch it on, select a block in the recall display and hold C until \"Print\" stops flashing (about 1 second) to print that block, or keep holding C until \"Print All\" appears to print every block. The stopwatch buttons do not work while printing, and the printout cannot be cancelled once started; do not switch off the printer or pull out the cord until it has finished. Put the cap back on the stopwatch jack when the printer is not in use.\u003c\/p\u003e\n\u003cp\u003eReceiving an auto-start time from the SVAS013 (SVAS013 and cord sold separately): Seiko's SVAS013 manual says to reset the SVAS011 and clear its memory first, because the auto-start time cannot be set while data is stored. Connect the two with the transfer cord and press the SVAS011's MODE button; the time is transferred automatically. If an error display appears, press MODE again.\u003c\/p\u003e\n\u003cp\u003eWater and care, as stated in Seiko's manual: the stopwatch withstands splashes and rain in everyday use. Seiko's manual says a 3 bar water resistant watch should not be used in water, and its water resistance table marks swimming and button operation while the stopwatch is wet as not allowed. Keep it away from solvents, cosmetic sprays, detergents and adhesives, and from strong magnetism. Left for a long time below -10 deg C or above +60 deg C, it may not work properly or may stop. Seiko recommends a check every 2 to 3 years, and its manual says the liquid crystal panel loses contrast and becomes hard to read after about 7 years of use.\u003c\/p\u003e\n\u003cp\u003eBattery: Seiko's manual says not to remove the battery yourself and to have it replaced with a battery made for Seiko watches. All stored data is erased when the battery is replaced, so print out any data you want to keep beforehand.\u003c\/p\u003e","brand":"EVERNEW","offers":[{"title":"Default Title","offer_id":46767247687843,"sku":"20260133","price":30000.0,"currency_code":"JPY","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0590\/1271\/0563\/files\/evernew-system-stopwatch-svas011egc302-7584193.jpg?v=1768534748"},{"product_id":"seiko-illuminating-light-svae301","title":"SEIKO Illuminating Light SVAE301 Stopwatch, LED Backlight, 100-Lap Memory, Double Repeat Timer, 5 Bar Water Resistant","description":"\u003ch2\u003eProduct Description\u003c\/h2\u003e\n\u003cp\u003eThe SVAE301 is a digital stopwatch in Seiko's Illuminating Light (イルミネーティングライト) series from Seiko Watch Corporation of Tokyo, Japan, built on Seiko's stopwatch caliber S058. Seiko's stopwatch lineup describes the series as a type with a built-in light that can be used in dark places. One press of the LIGHT button lights the whole display for about 3 seconds; Seiko's manual explains that a light guide panel spreads the light of the LED evenly over the entire display.\u003c\/p\u003e\n\u003cp\u003eThe stopwatch times in 1\/100 second units up to 100 hours and shows two times at once, in one of three displays: lap time with total time, lap time with running lap time (the lap still in progress), or split time with total time. Up to 100 lap or split times are kept in memory and can be recalled while the stopwatch is still timing or after it has stopped. The lap\/split count is shown up to 999; only the first 100 times are stored.\u003c\/p\u003e\n\u003cp\u003eThe double repeat timer runs two countdown timers one after the other and repeats the cycle, which Seiko describes as convenient for interval training. Each timer can be set from 10 seconds to 99 hours 59 minutes 59 seconds in one-second steps, the cycle can repeat 1 to 100 times or continuously, and the two timers end with beeps in different tones. When it is not timing, the SVAE301 works as a clock with a full auto calendar (to 31 December 2055) and a daily alarm.\u003c\/p\u003e\n\u003cp\u003eSeiko gives a battery life of about 3 years in normal mode, or about 7 years in eco mode, in which the display goes blank after one hour without use. The stopwatch leaves the factory in normal mode. It is rated 5 bar water resistant, which Seiko's manual explains as withstanding accidental splashes of water or rain.\u003c\/p\u003e\n\u003ch2\u003eProduct Specification\u003c\/h2\u003e\n\u003cp\u003e\n- Maker: Seiko Watch Corporation, Tokyo, Japan\u003cbr\u003e\n- Product name: SEIKO Illuminating Light stopwatch\u003cbr\u003e\n- Model: SVAE301\u003cbr\u003e\n- Caliber: S058\u003cbr\u003e\n- JAN: 4954628544216\u003cbr\u003e\n- Movement: battery-powered quartz\u003cbr\u003e\n- Accuracy: 0.0012% (30 seconds per month) at normal temperature\u003cbr\u003e\n- Stopwatch: 1\/100 second units, 100-hour counter\u003cbr\u003e\n- Display: two rows of digits and a dot-matrix display; lap time and total time, lap time and running lap time, or split time and total time\u003cbr\u003e\n- Lap\/split memory: up to 100 times, recallable during and after timing\u003cbr\u003e\n- Lap\/split count display: up to 999\u003cbr\u003e\n- Double repeat timer: two countdown timers, each settable from 10 seconds to 99 h 59 min 59 s in 1-second steps; 1 to 100 repeats or continuous; warning beep 3 seconds before time-up; different time-up tones for Timer 1 and Timer 2\u003cbr\u003e\n- Alarm: daily alarm, sounds for about 20 seconds\u003cbr\u003e\n- Clock and calendar: hour, minute, second, year, month, date and day of the week; 12- or 24-hour display; full auto calendar to 31 December 2055\u003cbr\u003e\n- Light: built-in LED, lights the entire display for about 3 seconds per press\u003cbr\u003e\n- Eco mode (automatic shut-off): display goes blank after 1 hour without operation; normal mode is the factory setting\u003cbr\u003e\n- Button confirmation sound: can be switched on or off\u003cbr\u003e\n- Water resistance: 5 bar (Seiko class: reinforced water resistance for everyday use)\u003cbr\u003e\n- Case: plastic\u003cbr\u003e\n- Glass: acrylic\u003cbr\u003e\n- Case thickness: 23.4 mm\u003cbr\u003e\n- Weight: 71.0 g\u003cbr\u003e\n- Strap: neck strap\u003cbr\u003e\n- Battery: SEIKO CR2032, 1 piece (not rechargeable); battery-end warning on the display\u003cbr\u003e\n- Battery life: approx. 3 years, or approx. 7 years with eco mode on. The battery is fitted at the factory to check the stopwatch, so its life may be shorter\u003cbr\u003e\n- Operating temperature: -10 to +60 deg C (0 to 50 deg C recommended)\u003cbr\u003e\n- Instruction manual: Seiko publishes the S058 manual on its website in Japanese and in English\u003cbr\u003e\n- Sources: Seiko's SVAE301 product page, Seiko's Illuminating Light feature page, and the Seiko S058 instruction manual\n\u003c\/p\u003e\n\u003ch2\u003eUsage\u003c\/h2\u003e\n\u003cp\u003eSeiko's manual labels the buttons A to E, and their names are printed on the case: A (LAP\/SPLIT, RESET; SET in the setting displays), B (RECALL), C (START\/STOP; SELECT in the setting displays), D (MODE) and E (LIGHT). Press MODE to move through the time\/calendar display, the three stopwatch displays (lap time, running lap time and split time), the timer display and the alarm display.\u003c\/p\u003e\n\u003cp\u003eTiming: reset the stopwatch to zero before you start. START\/STOP starts and stops timing; pressing it again restarts the count from where it stopped, so elapsed time can be added up over several runs. While timing, LAP\/SPLIT records a lap in the lap time or running lap time display, or a split in the split time display. Once the stopwatch is stopped, LAP\/SPLIT resets it.\u003c\/p\u003e\n\u003cp\u003eRecalling times: press RECALL. During timing the newest time comes up first; after timing, the oldest. Each press of START\/STOP steps from older to newer times, and each press of LAP\/SPLIT from newer to older. Press RECALL again to return to the stopwatch display. Stored times stay in memory after a reset and can be recalled until a new measurement is started.\u003c\/p\u003e\n\u003cp\u003eDouble repeat timer: in the timer display, hold RECALL for 2 seconds, choose the digits with SELECT (START\/STOP) and change them with SET (LAP\/SPLIT); set Timer 1, Timer 2 and the number of repeats, then press RECALL. Press START\/STOP to start. A warning beep sounds 3 seconds before each timer runs out, the time-up beep sounds for 5 seconds, and the next timer starts. To use a single repeat timer, set the timer you do not need to 00:00'00. Press any of buttons A to D to stop a beep.\u003c\/p\u003e\n\u003cp\u003eClock, alarm and eco mode: the time, the calendar and the alarm are set the same way, by holding RECALL for 2 seconds in the time\/calendar or alarm display. In the time\/calendar setting display you also choose 12- or 24-hour display and switch eco mode (automatic shut-off) on or off. In the time\/calendar display, START\/STOP turns the button confirmation sound on or off; in the alarm display, it turns the alarm on or off. With eco mode on, the display goes blank after one hour without use, shows the current time once every 10 seconds, and does not go blank while the stopwatch or timer is running; the alarm still sounds. Press any of buttons A to D to bring the display back.\u003c\/p\u003e\n\u003cp\u003eResetting the IC: if the display looks abnormal, press buttons A, B, C and D together for 2 to 3 seconds. This deletes all stored data; set the time, calendar and alarm again afterwards.\u003c\/p\u003e\n\u003cp\u003eWater and care, as stated in Seiko's manual: the 5 bar rating covers accidental splashes of water and rain. Do not operate the buttons when the stopwatch is wet or in water. Peel off any protective film or sticker on the case back before use. Keep the stopwatch away from solvents, mercury, cosmetic sprays, detergents, adhesives and paints, from strong shocks, and from objects that give off strong static electricity, such as TV screens. Long exposure to direct sunlight can turn the display black, and long periods below -10 deg C can make the time drift slightly, the digits change slowly and the light dim; all recover at normal temperature. Take care that the neck strap does not catch on anything or wind around your neck. Seiko recommends a check every 2 to 3 years, and gives the normal life of the liquid crystal panel as about 7 years.\u003c\/p\u003e\n\u003cp\u003eBattery: do not remove the battery yourself. If the battery has to be taken out, keep it out of the reach of children; if a child swallows it, see a doctor at once. Never short-circuit, heat or recharge the battery, or put it in a fire. Battery life can be shorter than stated if the stopwatch is used more than 3 hours a day, the double repeat timer more than 5 times a day, the alarm more than once a day, the light more than 3 times a day, or the confirmation sound more than 50 times a day. The light gets dimmer as the battery runs down. When all segments flash in the time\/calendar display, or the battery mark flashes in the other displays, the stopwatch may stop within 2 to 3 days. Seiko's manual recommends having the battery replaced by a Seiko dealer with a Seiko CR2032.\u003c\/p\u003e","brand":"SEIKO","offers":[{"title":"Default Title","offer_id":47357711679651,"sku":"20260843","price":11000.0,"currency_code":"JPY","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0590\/1271\/0563\/files\/seiko-illuminating-light-svae301-1959060.jpg?v=1772247127"},{"product_id":"seiko-solar-interval-timer-stylish-silver-svaj101","title":"SEIKO Interval Timer SVAJ101 Solar Stopwatch, Double Repeat Timer, 300-Lap Memory, 5 Bar Water Resistant, Silver","description":"\u003ch2\u003eProduct Description\u003c\/h2\u003e\n\u003cp\u003eThe SVAJ101 is a solar-powered digital stopwatch from Seiko Watch Corporation of Tokyo, Japan, in Seiko's Interval Timer series and built on Seiko's stopwatch caliber S062. Seiko describes the series as a solar stopwatch with a \"double repeat timer\" suited to interval training. The SVAJ101 is the silver model; its face reads \"INTERVAL TIMER\", \"SOLAR\" and \"WATER RESISTANT 5 BAR\".\u003c\/p\u003e\n\u003cp\u003eThe double repeat timer has two countdown timers that run one after the other: when Timer 1 reaches zero, Timer 2 starts, and when Timer 2 reaches zero, Timer 1 starts again. Each timer can be set from 10 seconds to 99 hours 59 minutes 59 seconds in 1-second steps, and the cycle repeats 1 to 100 times, or continuously until you stop it. A pre-warning beep sounds from 3 seconds before zero, and the two timers use different tones, so you can tell which one has ended. If one timer is set to zero, the other works as a single repeat timer.\u003c\/p\u003e\n\u003cp\u003eThe stopwatch measures in 1\/100 second units up to 100 hours. Its display has two rows of digits plus a dot-matrix line, and shows lap time with total time, lap time with running lap time (the lap in progress), or split time with total time. Up to 300 lap or split times are stored automatically and can be called up during or after timing, and the lap\/split count is shown up to 999. Its time\/calendar display shows the time and a full auto calendar with the day of the week.\u003c\/p\u003e\n\u003cp\u003eIt runs on light through a solar panel built into the display. Seiko gives about 6 months of operation after a full charge with no further light (based on 3 hours of stopwatch use and 20 hours in power save per day), and about 2 years in power save. There is no disposable battery to change. The built-in rechargeable battery can slowly lose capacity over long use, and Seiko's manual says not to remove it yourself. Seiko also lists a power save function that turns the display off after 1, 3, 6 or 12 hours without use, a sound on\/off switch for the button beeps, and display contrast adjustment.\u003c\/p\u003e\n\u003ch2\u003eProduct Specification\u003c\/h2\u003e\n\u003cp\u003e\n- Maker: Seiko Watch Corporation, Tokyo, Japan\u003cbr\u003e\n- Product name: SEIKO Interval Timer solar stopwatch\u003cbr\u003e\n- Model: SVAJ101 (silver)\u003cbr\u003e\n- Caliber: S062\u003cbr\u003e\n- JAN: 4954628424051\u003cbr\u003e\n- Drive: solar; rechargeable secondary battery, 1 piece\u003cbr\u003e\n- Operating time: approx. 6 months after a full charge without light (3 hours of stopwatch use and 20 hours of power save per day); approx. 2 years in power save\u003cbr\u003e\n- Accuracy: average monthly rate within +\/-30 seconds (+\/-0.0012%) at normal temperatures of 5 to 35 deg C\u003cbr\u003e\n- Stopwatch: 1\/100 second units, 100-hour counter; split, lap and running lap modes\u003cbr\u003e\n- Display: two rows of digits plus a dot-matrix line\u003cbr\u003e\n- Lap\/split memory: up to 300 times, recallable during and after timing (timing continues past 300, but only the first 300 are stored)\u003cbr\u003e\n- Lap\/split count display: up to 999\u003cbr\u003e\n- Double repeat timer: Timer 1 and Timer 2, each 10 seconds to 99 hours 59 minutes 59 seconds in 1-second steps; 1 to 100 repetitions or continuous (\"---\"); pre-warning beep from 3 seconds before zero; time-up beep of about 5 seconds; a different tone for each timer\u003cbr\u003e\n- Clock and calendar: 12-hour or 24-hour time; full auto calendar with day of the week, from January 1, 2013 to December 31, 2062\u003cbr\u003e\n- Power save: display turns off after 1, 3, 6 or 12 hours without button use (not while the stopwatch or timer is running); sleep mode after about 72 hours in power save\u003cbr\u003e\n- Sound: button operation beep can be switched on or off\u003cbr\u003e\n- Display contrast: adjustable in 5 steps (-2 to +2)\u003cbr\u003e\n- Water resistance: 5 bar (Seiko class: reinforced water resistance for everyday use)\u003cbr\u003e\n- Glass: acrylic\u003cbr\u003e\n- Case back: fixed with 6 screws\u003cbr\u003e\n- Case thickness: 21.0 mm\u003cbr\u003e\n- Operating temperature: -10 to +60 deg C (display works from 0 to +50 deg C)\u003cbr\u003e\n- Instruction manual: Seiko publishes the S061\/S062 manual on its website, with Japanese and English in one file\u003cbr\u003e\n- Sources: Seiko's SVAJ101 product page, Seiko's Interval Timer feature page, and the Seiko S061\/S062 instruction manual\n\u003c\/p\u003e\n\u003ch2\u003eUsage\u003c\/h2\u003e\n\u003cp\u003eSeiko's manual labels the buttons A to D: A (LAP\/SPLIT RESET) takes a lap or split time while timing and resets the stopwatch once it is stopped; B (RECALL) calls up stored times; C (START\/STOP) starts and stops; D (MODE, on the front of the case) moves between the time\/calendar display, the split, lap and running lap stopwatch displays, and the timer display.\u003c\/p\u003e\n\u003cp\u003eRecalling times: press B. After the stopwatch has stopped, the oldest time comes up first; while it is still timing, the newest comes up first. Press A or C to step through them. Resetting the stopwatch does not delete stored times; they are cleared when a new measurement starts.\u003c\/p\u003e\n\u003cp\u003eDouble repeat timer: press D to show the timer display, then hold B for 2 seconds. Set the hours, minutes and seconds of Timer 1 and Timer 2 and the number of repetitions: A changes the flashing value (hold it to advance quickly) and C moves to the next item. Press B to return to the timer display. Press C to start, stop and restart, and A to reset the timer to its set times. Seiko's manual uses 3 minutes on Timer 1 and 1 minute on Timer 2, repeated 10 times, as its example. Pressing any button silences the current beep; the next countdown still beeps.\u003c\/p\u003e\n\u003cp\u003eClock and settings: in the time\/calendar display, hold B for 2 seconds, then press C to step through the settings (time, calendar, 12\/24-hour display, power save delay and display contrast) and A to change each one; press B to finish. The day of the week sets itself. In the time\/calendar display, press C to turn the button beep on or off. When you time in the dark, Seiko recommends setting the power save delay longer than the time you will be timing.\u003c\/p\u003e\n\u003cp\u003eCharging: keep the display facing the light. Seiko's manual gives the light needed for one day of operation as about 5 minutes outdoors on a sunny day, about 55 minutes by a window on a sunny day, about 95 minutes by a window on a cloudy day, or about 15 hours under indoor fluorescent light. Charge it well before first use and after it has stopped. Kept in a drawer or locker, or left face down, it may stop for lack of charge. Do not charge it close to photo lights, spotlights or incandescent bulbs, or on a car dashboard, and keep it below 50 deg C. When the battery indicator shows very low, the time-up beep does not sound; when it shows that charging is required, any timing in progress is reset and stored times may be lost. If the display shows abnormal readings, press all four buttons together for 2 to 3 seconds to reset the system; this erases all stored times and the time and date settings.\u003c\/p\u003e\n\u003cp\u003eWater and care, as stated in Seiko's manual: the 5 bar rating means the stopwatch resists splashes during sports where it may get wet. Do not operate the buttons when it is wet or underwater; do not use it for scuba or saturation diving; avoid baths and saunas; do not hold it under running tap water. After contact with sea water, rinse it in a bowl of fresh water and wipe it dry. Do not leave it for long in places below 5 deg C or above 35 deg C. Seiko recommends an inspection and overhaul every 3 to 4 years, and gives the normal life of the liquid crystal panel as about 7 years.\u003c\/p\u003e","brand":"SEIKO","offers":[{"title":"Default Title","offer_id":47357712990371,"sku":"20260844","price":11000.0,"currency_code":"JPY","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0590\/1271\/0563\/files\/seiko-solar-interval-timer-stylish-silver-svaj101-3569803.jpg?v=1772247129"},{"product_id":"casio-stopwatch-with-lap-split-time-2-memories-50m-water-resistant-silent-mode-white-hs-70w-8jh","title":"CASIO Stopwatch with Lap\/Split Time  2 Memories  50m Water Resistant  Silent Mode  White HS-70W-8JH","description":"\u003ch2\u003eProduct Description\u003c\/h2\u003e\n\u003cp\u003eThis digital stopwatch is designed for serious timing performance in any environment, offering 5 ATM water resistance for use in the rain, at the pool, or by the sea. Its ergonomic body with a central contour fits comfortably in the hand, while the wide strap feels secure and comfortable whether worn around the neck or wrapped around the wrist.\u003c\/p\u003e\n\u003cp\u003eEnjoy ultra-precise 1\/1000-second measurement for up to 10 hours, with standard timekeeping, lap and split timing, and simultaneous ranking display from 1st to 100th place. The stopwatch stores up to 100 lap\/split records in 2 separate memory sets, and also functions as a clock and calendar with a full auto-calendar and 12\/24-hour display options. An operation sound ON\/OFF feature lets you mute key beeps when needed.\u003c\/p\u003e\n\u003cp\u003eCompact and lightweight at approximately 8.3 × 6.4 × 2.4 cm and about 85 g, it is made from durable resin and powered by a single CR2032 button battery with an approximate 5-year life. Included in the box are the user manual, warranty, and one CR2032 battery so you can start using it right away.\u003c\/p\u003e","brand":"CASIO","offers":[{"title":"Default Title","offer_id":47357714137251,"sku":"20260845","price":8180.0,"currency_code":"JPY","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0590\/1271\/0563\/files\/casio-stopwatch-with-lapsplit-time-2-memories-50m-water-resistant-silent-mode-white-hs-70w-8jh-4857423.jpg?v=1772247130"},{"product_id":"rhythm-citizen-digital-stopwatch-8rda55-002-water-resistant-black","title":"CITIZEN RHYTHM Digital Stopwatch 8RDA55-002  Water-Resistant  Black","description":"\u003ch2\u003eProduct Description\u003c\/h2\u003e\n\u003cp\u003eThis compact rain-resistant stopwatch is designed for reliable performance in daily training and outdoor activities. Its lightweight plastic frame makes it easy to carry and comfortable to hold.\u003c\/p\u003e\n\u003cp\u003ePowered by a single LR44 battery, this stopwatch measures approximately 75 × 60 × 19 mm and weighs about 42 g, offering a practical balance of portability and durability.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eCountry of origin: China\u003c\/li\u003e\n\u003cli\u003eMaterial: Plastic frame\u003c\/li\u003e\n\u003cli\u003ePower source: 1 x LR44 battery\u003c\/li\u003e\n\u003cli\u003eSize: 75 × 60 × 19 mm\u003c\/li\u003e\n\u003cli\u003eWeight: 42 g\u003c\/li\u003e\n\u003cli\u003eRain-resistant design\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"CITIZEN","offers":[{"title":"Default Title","offer_id":47357715611811,"sku":"20260846","price":2980.0,"currency_code":"JPY","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0590\/1271\/0563\/files\/citizen-rhythm-digital-stopwatch-8rda55-002-water-resistant-black-5112639.jpg?v=1772247127"},{"product_id":"hs-3c-8ajh-stopwatch","title":"CASIO HS-3C-8AJH Stopwatch","description":"\u003ch2\u003eProduct Description\u003c\/h2\u003e\n\u003cp\u003eDiscover Casio, a trusted Japanese brand known worldwide for its reliable digital watches, calculators, and everyday electronics. Designed for both style and performance, Casio products combine innovative technology with practical functionality.\u003c\/p\u003e\n\u003cp\u003eWhether you are looking for a durable timepiece, a precise calculator, or versatile digital devices, Casio delivers long-lasting quality that fits active, modern lifestyles across the globe.\u003c\/p\u003e","brand":"CASIO","offers":[{"title":"Default Title","offer_id":47357718429859,"sku":"20260847","price":6490.0,"currency_code":"JPY","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0590\/1271\/0563\/files\/casio-hs-3c-8ajh-stopwatch-3992072.jpg?v=1771696996"},{"product_id":"rhythm-citizen-waterproof-stopwatch-with-split-time-pace-stroke-black-lc058-a02","title":"CITIZEN RHYTHM Waterproof Stopwatch with Split Time  Pace \u0026 Stroke  Black LC058-A02","description":"\u003ch2\u003eProduct Description\u003c\/h2\u003e\n\u003cp\u003eCompact stopwatch with plastic frame, measuring approximately 81 × 66 × 23 mm and weighing about 80 g. Powered by one CR2032 battery (included). Made in China and supplied with instruction manual and warranty card.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eDrip-resistant (JIS drip-proof type 2): suitable for poolside use, but not fully waterproof\u003c\/li\u003e\n\u003cli\u003eFunctions: simple timing, accumulated (lap) timing, split timing, simultaneous timing for 1st and 2nd place\u003c\/li\u003e\n\u003cli\u003eTime display with 12\/24-hour switchable format\u003c\/li\u003e\n\u003cli\u003eElectronic sound alarm and countdown timer\u003c\/li\u003e\n\u003cli\u003ePace count function and calendar display\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"CITIZEN","offers":[{"title":"Default Title","offer_id":47357719085219,"sku":"20260848","price":6500.0,"currency_code":"JPY","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0590\/1271\/0563\/files\/citizen-rhythm-waterproof-stopwatch-with-split-time-pace-stroke-black-lc058-a02-7960877.jpg?v=1771696999"},{"product_id":"seiko-solar-standard-yellow-watch-svaj003","title":"SEIKO SVAJ003 Standard Solar Stopwatch, 1\/100 s, 100-Hour, 300-Lap Memory, 5 Bar Water Resistant, Yellow","description":"\u003ch2\u003eProduct Description\u003c\/h2\u003e\n\u003cp\u003eThe SVAJ003 is a solar-powered digital stopwatch in Seiko's Standard series (スタンダード), made by Seiko Watch Corporation of Tokyo, Japan, and built on Seiko's stopwatch caliber S061. Seiko describes the Standard series as its standard type of stopwatch with a solar battery that also takes lap and split times. The SVAJ003 has a yellow case, as shown in Seiko's product image.\u003c\/p\u003e\n\u003cp\u003eIt times in 1\/100 second units on a 100-hour counter. The two-row display, with a dot-matrix row above it, shows lap time and total time, lap time and running lap time (the lap in progress), or split time and total time, depending on the stopwatch display you choose. Lap and split times are stored automatically, up to 300 of them, and can be recalled while the stopwatch is still running or after it has stopped. The lap\/split count is shown up to 999.\u003c\/p\u003e\n\u003cp\u003eA solar panel built into the display charges a rechargeable (secondary) battery. Seiko gives the running time as about 6 months from a full charge without any light, based on 3 hours of stopwatch use and 20 hours in power save mode a day, and about 2 years in power save mode. Seiko's Standard series page lists the solar battery as needing no battery changes; its manual adds that the capacity of the rechargeable battery can decline gradually with long use or depending on conditions of use, and that the stopwatch should then be repaired.\u003c\/p\u003e\n\u003cp\u003eWhen the stopwatch is not in use, the SVAJ003 shows the time and a full auto calendar with year, month, date and day of the week. A power save function turns the display off after a set time without operation, the operation beep can be switched off, and the display contrast can be adjusted. Seiko rates the case at 5 bar water resistance, which it classes as reinforced water resistance for everyday use.\u003c\/p\u003e\n\u003ch2\u003eProduct Specification\u003c\/h2\u003e\n\u003cp\u003e\n- Maker: Seiko Watch Corporation, Tokyo, Japan\u003cbr\u003e\n- Product name: SEIKO Standard solar stopwatch\u003cbr\u003e\n- Model: SVAJ003\u003cbr\u003e\n- Caliber: S061\u003cbr\u003e\n- Color: yellow\u003cbr\u003e\n- Power: solar; rechargeable secondary battery, 1 piece; solar panel built into the display\u003cbr\u003e\n- Running time: about 6 months from a full charge without light (3 hours of stopwatch use and 20 hours of power save per day); about 2 years in power save mode\u003cbr\u003e\n- Accuracy: average monthly rate +\/-30 seconds (Seiko product page); the manual states within +\/-30 seconds per month (+\/-0.0012%) at normal temperatures of 5 to 35 deg C\u003cbr\u003e\n- Stopwatch: 1\/100 second units, 100-hour counter\u003cbr\u003e\n- Display: two rows plus a dot-matrix indication; lap, split or running lap display selectable\u003cbr\u003e\n- Lap\/split memory: up to 300, recallable during and after timing (timing continues past 300, but only the first 300 are stored)\u003cbr\u003e\n- Lap\/split count display: up to 999\u003cbr\u003e\n- Clock and calendar: 12-hour or 24-hour time; full auto calendar with day of the week, from January 1, 2013 to December 31, 2062\u003cbr\u003e\n- Power save: display turns off after 1, 3, 6 or 12 hours without operation (selectable); not while the stopwatch is running\u003cbr\u003e\n- Operation beep: can be switched on or off\u003cbr\u003e\n- Display contrast: adjustable in 5 steps (-2 to +2)\u003cbr\u003e\n- Water resistance: 5 bar (Seiko class: reinforced water resistance for everyday use)\u003cbr\u003e\n- Glass: acrylic\u003cbr\u003e\n- Case back: fixed with 6 screws\u003cbr\u003e\n- Case thickness: 21.0 mm\u003cbr\u003e\n- Operating temperature: -10 to +60 deg C (display function from 0 to +50 deg C)\u003cbr\u003e\n- Instruction manual: Seiko publishes the S061\/S062 manual on its website as a PDF with Japanese and English sections\u003cbr\u003e\n- Sources: Seiko's SVAJ003 product page, Seiko's Standard series feature page, and the Seiko S061\/S062 instruction manual\n\u003c\/p\u003e\n\u003ch2\u003eUsage\u003c\/h2\u003e\n\u003cp\u003eButtons, as labeled in Seiko's manual: A (LAP\/SPLIT RESET) takes a lap or split time while timing and resets the stopwatch once it is stopped; B (RECALL) opens and closes the memory recall display; C (START\/STOP) starts and stops timing, and pressing it again after a stop continues the total time; D (MODE) switches between the time\/calendar display and the split, lap and running lap stopwatch displays. In the lap and running lap displays, pressing C to stop also records the last lap.\u003c\/p\u003e\n\u003cp\u003eRecalling times: press B. After a stop, the oldest record is shown first; while the stopwatch is running, the newest is shown first. Step through the records with A and C. Resetting the stopwatch does not erase the memory; the stored records are cleared when a new timing run starts.\u003c\/p\u003e\n\u003cp\u003eTime and calendar: in the time\/calendar display, hold B for 2 seconds. C selects the item to change and A changes it; the same setting display also holds the 12\/24-hour choice, the power save time and the contrast. Press B to finish; the day of the week sets itself from the date. In the time\/calendar display, C switches the operation beep on or off. The double repeat timer described in the shared S061\/S062 manual belongs to caliber S062 (Seiko's Interval Timer models) and is not on the SVAJ003.\u003c\/p\u003e\n\u003cp\u003eCharging: expose the display to light. Seiko's manual gives the charging time needed for one day of operation as about 5 minutes outdoors on a sunny day (100,000 lux), about 55 minutes by a window on a sunny day (10,000 lux), about 95 minutes by a window on a cloudy day (5,000 lux), and about 15 hours under indoor fluorescent light (500 lux). The stopwatch can stop if it is kept in a drawer or locker or left with its display facing down. When the charge runs very low, a running measurement is reset and stored records may be lost. Do not charge it close to photo lights, spotlights or incandescent lamps or on a car dashboard, and keep it below 50 deg C. After about 3 days in power save mode it enters sleep mode, which resets the stopwatch; press any button to wake it.\u003c\/p\u003e\n\u003cp\u003eWater and care, as stated in Seiko's manual: at 5 bar the stopwatch withstands splashes during sports in which it may get wet. Do not operate the buttons underwater or while the stopwatch is wet. Do not use it for scuba diving, do not use it in a bath or sauna, and do not hold it under running tap water. Wipe off moisture, sweat and dirt with a soft cloth. If the display shows abnormal readings, press all four buttons together for 2 to 3 seconds to reset it; this erases all stored records and the time and date must be set again. Seiko recommends an overhaul about every 3 to 4 years and gives the normal life of the liquid crystal panel as about 7 years.\u003c\/p\u003e\n\u003cp\u003eBattery: do not remove the rechargeable battery yourself. Seiko states that replacing it requires professional knowledge and skill, and that fitting an ordinary silver oxide battery can cause heat, bursting or ignition.\u003c\/p\u003e","brand":"SEIKO","offers":[{"title":"Default Title","offer_id":47357719969955,"sku":"20260849","price":10680.0,"currency_code":"JPY","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0590\/1271\/0563\/files\/seiko-solar-standard-yellow-watch-svaj003-8733995.jpg?v=1771696994"},{"product_id":"seiko-solar-interval-timer-power-red-svaj103","title":"SEIKO SVAJ103 Interval Timer Solar Stopwatch, Double Repeat Timer, 300-Lap Memory, 5 Bar Water Resistant, Red","description":"\u003ch2\u003eProduct Description\u003c\/h2\u003e\n\u003cp\u003eThe SVAJ103 is a solar-powered digital stopwatch in the Interval Timer series (インターバルタイマー) from Seiko Watch Corporation of Tokyo, Japan. It runs on Seiko's caliber S062. Seiko describes the series as a solar stopwatch with a \"double repeat timer\" function that suits interval training. The front of the case reads \"INTERVAL TIMER\". The case is red, as in Seiko's product image.\u003c\/p\u003e\n\u003cp\u003eThe double repeat timer has two countdown timers that run one after the other. When Timer 1 reaches zero, Timer 2 starts, and when Timer 2 reaches zero, Timer 1 starts again. Each timer can be set in 1-second steps from 10 seconds to 99 hours 59 minutes 59 seconds. The number of repetitions can be set from 1 to 100, or to \"- - -\" to repeat until you stop it. Each timer beeps for the last 3 seconds before zero and sounds for about 5 seconds at zero. Timer 1 and Timer 2 use different sounds, so you can tell which one has finished. If one of the timers is set to zero, the other works as an ordinary repeat timer.\u003c\/p\u003e\n\u003cp\u003eThe stopwatch measures in 1\/100 second units on a 100-hour counter. It has a two-row display plus a dot-matrix row, and you can switch between split, lap and running lap modes. Up to 300 lap or split times are stored automatically. They can be recalled while timing is still running or after it stops, and the lap\/split count is shown up to 999. A separate time\/calendar display, selected with the mode button, shows the time and a full auto calendar with the day of the week.\u003c\/p\u003e\n\u003cp\u003eThe solar panel is built into the display. Seiko states that a full charge runs the stopwatch for about 6 months without light, based on 3 hours of stopwatch use and 20 hours of power save per day, and for about 2 years in power-save mode. Seiko's feature page lists the solar battery as needing no battery changes. The manual adds that the capacity of the rechargeable battery can decline gradually with long use.\u003c\/p\u003e\n\u003ch2\u003eProduct Specification\u003c\/h2\u003e\n\u003cp\u003e\n- Maker: Seiko Watch Corporation, Tokyo, Japan\u003cbr\u003e\n- Product name: SEIKO Interval Timer solar stopwatch\u003cbr\u003e\n- Model: SVAJ103\u003cbr\u003e\n- Caliber: S062\u003cbr\u003e\n- JAN: 4954628424068\u003cbr\u003e\n- Colour: red (as shown in Seiko's product image)\u003cbr\u003e\n- Drive: solar, with 1 rechargeable secondary battery\u003cbr\u003e\n- Operating time: approx. 6 months without light after a full charge (with 3 hours of stopwatch use and 20 hours of power save per day); approx. 2 years in power-save mode\u003cbr\u003e\n- Accuracy: average monthly rate within +\/-30 seconds (+\/-0.0012%) at normal temperatures of 5 to 35 deg C\u003cbr\u003e\n- Stopwatch: 1\/100 second units, 100-hour counter; split, lap and running lap modes\u003cbr\u003e\n- Display: two rows plus a dot-matrix row (5 x 35 dots)\u003cbr\u003e\n- Lap\/split memory: up to 300 times, recallable during and after timing\u003cbr\u003e\n- Lap\/split count display: up to 999\u003cbr\u003e\n- Double repeat timer: Timer 1 and Timer 2, each 10 seconds to 99 hours 59 minutes 59 seconds in 1-second steps; 1 to 100 repetitions or continuous (\"- - -\"); a different pre-warning and time-up sound for each timer\u003cbr\u003e\n- Clock and calendar: hour, minute and second in 12- or 24-hour format; full auto calendar with year, month, date and day of the week (January 1, 2013 to December 31, 2062)\u003cbr\u003e\n- Power save: the display turns off after 1, 3, 6 or 12 hours (selectable) without a button press, but not while the stopwatch or timer is running; sleep mode after 72 hours of power save\u003cbr\u003e\n- Other functions: operation beep on\/off; display contrast adjustable in 5 levels (-2 to +2)\u003cbr\u003e\n- Water resistance: 5 bar (Seiko class: reinforced water resistance for everyday use)\u003cbr\u003e\n- Glass: acrylic\u003cbr\u003e\n- Case thickness: 21.0 mm\u003cbr\u003e\n- Case back: fixed with 6 screws\u003cbr\u003e\n- Strap: black neck cord (as shown in Seiko's product image)\u003cbr\u003e\n- Operating temperature: -10 to +60 deg C (display function: 0 to +50 deg C)\u003cbr\u003e\n- Instruction manual: Seiko publishes the S061\/S062 manual on its website; the PDF has Japanese and English sections\u003cbr\u003e\n- Sources: Seiko's SVAJ103 product page, Seiko's Interval Timer feature page, and the Seiko S061\/S062 instruction manual\n\u003c\/p\u003e\n\u003ch2\u003eUsage\u003c\/h2\u003e\n\u003cp\u003eButtons: Seiko's manual labels the buttons A to D. A (LAP\/SPLIT, RESET) takes a lap or split time while the stopwatch is running and resets it once it has stopped. B (RECALL) opens and closes the memory. C (START\/STOP) starts and stops timing. D (MODE, below the display) moves between the time\/calendar display, the split, lap and running lap stopwatch displays, and the timer display.\u003c\/p\u003e\n\u003cp\u003eStopwatch: press D to choose split, lap or running lap, then press C to start. Press A for each lap or split, and press C to stop. In lap and running lap modes, the stop also counts as the last lap. To see stored times, press B. If you press B after stopping, the first time is shown. If you press B while timing is running, the latest time is shown. Then press A or C to step through the stored times. Resetting the stopwatch does not erase the memory. The stored times are cleared when the next timing run starts. You can time more than 300 laps, but only the first 300 are stored.\u003c\/p\u003e\n\u003cp\u003eDouble repeat timer: in the timer display, hold B for 2 seconds. Press A to change the flashing value and C to move to the next item, in this order: Timer 1 hours, minutes and seconds, then Timer 2 hours, minutes and seconds, then the repeat count. Press B to finish. Press C to start. Each press of C stops or restarts the timer, and A resets it to the set times. Press any button to stop a beep. This silences only that one sound.\u003c\/p\u003e\n\u003cp\u003eTime and calendar: in the time\/calendar display, hold B for 2 seconds. Press C to move through second, minute, hour, date, month, year, 12\/24-hour format, the power-save delay and the display contrast. Press A to change each value, and press B to finish. The day of the week is set automatically. In the time\/calendar display, press C to turn the operation beep on or off.\u003c\/p\u003e\n\u003cp\u003eCharging: put the display, where the solar panel is, in the light. Seiko's charging guide gives these times for one day of operation: about 5 minutes outdoors on a sunny day (100,000 lux), about 55 minutes by a window on a sunny day, about 95 minutes by a window on a cloudy day, or about 15 hours under indoor fluorescent light (500 lux). Before first use, or after the stopwatch has stopped because the battery ran out, charge it well. It can stop if it is kept in a drawer or locker, or left with the display facing down. When the battery icon shows the \"extremely low\" level, the time-up sound does not play. When the battery icon flashes to show that charging is needed, stored times may be lost, and a running stopwatch or timer is reset. While charging, keep the stopwatch below 50 deg C. Keep it away from photo lights, spotlights and incandescent bulbs, and do not leave it on a car dashboard in the sun. If you use the stopwatch or timer in the dark, Seiko recommends setting the power-save delay longer than you will be timing.\u003c\/p\u003e\n\u003cp\u003eWater and care, as stated in Seiko's manual: the 5 bar class can be used during sports where the stopwatch gets splashed. Do not press the buttons under water or while the stopwatch is wet. It is not for scuba or saturation diving. Do not use it in a bath or sauna. Do not run tap water directly onto it. After contact with sea water, wash it in a bowl of fresh water and wipe it dry. Do not remove the rechargeable battery yourself. Seiko's manual says replacing it needs specialist knowledge and skill, and that fitting an ordinary silver oxide battery in its place can cause heat, bursting or fire. If the display shows something abnormal, press all four buttons together for 2 to 3 seconds to reset the system. This erases all stored data, and the time and date have to be set again.\u003c\/p\u003e","brand":"SEIKO","offers":[{"title":"Default Title","offer_id":47357720821923,"sku":"20260850","price":12000.0,"currency_code":"JPY","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0590\/1271\/0563\/files\/seiko-solar-interval-timer-power-red-svaj103-7125915.jpg?v=1771696996"},{"product_id":"other-integrated-stopwatch-printer-system-gray","title":"SEIKO SVAS013 Printer-Integrated Stopwatch, 1\/100 sec, 300-Lap Memory, Auto Start","description":"\u003ch2\u003eProduct Description\u003c\/h2\u003e\n\u003cp\u003eThe SVAS013 is Seiko's printer-integrated stopwatch (プリンター一体型ストップウオッチ), a digital stopwatch with a built-in thermal printer, from Seiko Watch Corporation of Tokyo, Japan. It is built on Seiko's stopwatch caliber S149, and its face is marked \"SYSTEM STOPWATCH\" and \"300 LAP\/SPLIT MEMORY\". It times in 1\/100 second units on a 10-hour counter and shows three rows at once: the split time, the lap time, and either the total elapsed time or the lap time in progress.\u003c\/p\u003e\n\u003cp\u003eSeiko's manual describes the S149 as suited to timing large numbers of people at road races and marathons. Times can be printed as soon as they are taken, and each printout begins with the block number, the date and the start time, which Seiko notes makes records easy to sort and keep. Up to 300 lap and split times are kept in memory as numbered blocks, up to 100 blocks, without erasing earlier blocks. Stored times can be recalled while the stopwatch is still timing and printed again later, one block or all blocks at a time. The fastest lap of each block can be recalled.\u003c\/p\u003e\n\u003cp\u003eThe auto start function starts timing by itself at a preset time of day. With Seiko's connection cord 7504500, sold separately, the SVAS013 can pass its auto start time to Seiko's SVAS011 System Stopwatch (caliber S143), so that stopwatches at the start and at checkpoints begin timing at the same moment. A grip switch and a paper holder for longer roll paper are also available separately.\u003c\/p\u003e\n\u003cp\u003eThe SVAS013 is not water resistant. Seiko's manual states that it is not a water-resistant watch and that use in direct contact with water should be avoided.\u003c\/p\u003e\n\u003ch2\u003eProduct Specification\u003c\/h2\u003e\n\u003cp\u003e\n- Maker: Seiko Watch Corporation, Tokyo, Japan\u003cbr\u003e\n- Product name: SEIKO printer-integrated stopwatch (face marked \"SYSTEM STOPWATCH\")\u003cbr\u003e\n- Model: SVAS013\u003cbr\u003e\n- Caliber: S149\u003cbr\u003e\n- JAN: 4954628451415\u003cbr\u003e\n- Movement: battery-powered quartz\u003cbr\u003e\n- Accuracy: within +\/-15 seconds per month (+\/-0.0006%) at normal temperatures of 5 to 35 deg C\u003cbr\u003e\n- Stopwatch: 1\/100 second units, 10-hour counter; readout switchable between 1\/100 second and 1 second\u003cbr\u003e\n- Display: three rows showing split time, lap time, and total elapsed time or lap time in progress; lap\/split count 0 to 999\u003cbr\u003e\n- Memory: up to 300 lap\/split times in up to 100 blocks, each block stored with its start date and time; recall during timing; fastest-lap recall per block; 10-segment memory indicator (30 entries per segment). The block number and start time of each block also use memory, so the memory can fill before 300 lap\/split times are stored. Times taken after the memory is full are shown but not stored\u003cbr\u003e\n- Auto start: the stopwatch beeps and starts timing at a preset hour and minute. The auto start time can be transferred to Seiko SVAS011 stopwatches (caliber S143) with the connection cord 7504500 (sold separately)\u003cbr\u003e\n- Clock and calendar: 24-hour time; full auto calendar; ID number OFF or 01 to 99; display contrast adjustable in 10 levels\u003cbr\u003e\n- Printer: built-in thermal printer (model MTP102), thermal serial dot printing, left to right; approx. 1.5 lines per second; 13 digits per line; print mode switch for split time only, or split and lap times\u003cbr\u003e\n- Roll paper: thermal roll paper S-950 (38 mm wide, 2,400 mm or longer, approx. 700 lines per roll) is included. The longer S-951 roll (up to 2,800 lines) needs the paper holder SVAZ007; both are sold separately. Seiko states that only S-950 or S-951 should be used\u003cbr\u003e\n- Printer power: four AA dry batteries (DC 6 V). By Seiko's figures for continuous printing at 24 deg C: approx. 10,000 lines (about 14 rolls) with manganese batteries, approx. 20,000 lines (about 28 rolls) with alkaline batteries\u003cbr\u003e\n- Stopwatch battery: lithium SB-T74, 1 piece; battery-end warning (\"BATT\" flashes)\u003cbr\u003e\n- Stopwatch battery life: approx. 3 years, based on 3 hours of stopwatch use per day. The battery fitted at the factory is a monitor battery and may run out sooner\u003cbr\u003e\n- Water resistance: none (Seiko's manual: not a water-resistant watch)\u003cbr\u003e\n- Case: plastic. Seiko's manual states that an antibacterial agent is applied to the case surface and that the effect declines over time, depending on the conditions of use\u003cbr\u003e\n- Glass: Hardlex\u003cbr\u003e\n- Case thickness: 29.0 mm\u003cbr\u003e\n- Weight: 211.0 g\u003cbr\u003e\n- Operating temperature: stopwatch -10 to +60 deg C (display temperature range 0 to +50 deg C); printer 0 to 40 deg C\u003cbr\u003e\n- Controls and connections: START\/STOP and LAP\/SPLIT RESET buttons; STOP-W., A\/S SET and TIME mode buttons; 1\/100 readout button; RECALL button; lock lever for the START\/STOP button; printer power switch, paper advance switch and print mode switch; jack for auto start transfer; jack and selector switch for the grip switch\u003cbr\u003e\n- Options (sold separately): connection cord 7504500, grip switch, paper holder SVAZ007, roll paper S-950 and S-951\u003cbr\u003e\n- Instruction manual: Seiko publishes the S149 manual on its website in Japanese and in English\u003cbr\u003e\n- Sources: Seiko's SVAS013 product page, Seiko's printer-integrated stopwatch feature page, and the Seiko S149 instruction manual (Japanese and English editions)\n\u003c\/p\u003e\n\u003ch2\u003eUsage\u003c\/h2\u003e\n\u003cp\u003eSeiko's manual labels the two large buttons A and B: A (START\/STOP) starts and stops timing; B (LAP\/SPLIT, RESET) takes a split and lap while timing and resets the stopwatch once it is stopped. The STOP-W., A\/S SET and TIME buttons select the stopwatch, auto start setting and time\/calendar modes; 1\/100 switches the readout between 1\/100 second and 1 second; RECALL calls up and prints stored times. After timing has started, the lock lever can be slid down to lock the START\/STOP button so that timing is not stopped by mistake.\u003c\/p\u003e\n\u003cp\u003ePrinting while timing: turn the printer power switch on before you start, and set the print mode switch to split time only, or to split and lap times. When timing starts, the printer prints the ID number (if set), the block number, the date and the start time, then each time as it is taken. Printing stored times: turn the printer on, open the memory recall display and hold RECALL. Release it when \"Print\" stops flashing to print the selected block, or keep holding until \"Print All\" appears to print every block. While stored times are being printed, the stopwatch buttons do not work and the printout cannot be cancelled halfway. In the time\/calendar mode, with the stopwatch reset and the printer on, A starts a time-of-day printout, each press of B prints the time of day, and A stops it; these times are not stored in memory.\u003c\/p\u003e\n\u003cp\u003eAuto start: press A\/S SET, press B and set the minutes and then the hours with A, press B again to enter the time, then press STOP-W. to return to the stopwatch mode. Check that the third row of the display changes to the current time; otherwise auto start does not work. Setting an auto start time clears all stored data. To pass the time to an SVAS011, connect it to the auto start jack with the connection cord, keep the SVAS013 in the stopwatch mode, reset the SVAS011 and clear its memory, then press the SVAS011's mode button. To cancel auto start on the SVAS013, press A\/S SET.\u003c\/p\u003e\n\u003cp\u003eMemory: to clear it, reset the stopwatch, press RECALL, then hold B for more than 1.5 seconds. All data is erased at once; single blocks cannot be deleted. All stored data is also erased when the stopwatch battery is replaced, so print out anything you want to keep first.\u003c\/p\u003e\n\u003cp\u003eGrip switch (optional): connect it and slide the grip switch selector on the right side up. Each press then starts timing or takes a split and lap; buttons A and B do not work while the selector is up. The grip switch cannot stop timing: slide the selector down, then press A to stop and B to reset.\u003c\/p\u003e\n\u003cp\u003eCare, as stated in Seiko's manual: keep the SVAS013 away from water. Turn the printer power off when the printer is not in use, do not run the printer without roll paper, and do not pull the paper out or back while it is printing. Put the caps on the jacks when no option is connected. When printing becomes slow, faint or uneven, replace the four AA batteries; Seiko suggests alkaline batteries for use at low temperatures. Keep unused thermal paper in a box in a cool, dry place away from light, do not touch the printing surface, and keep printouts away from strong light, heat, humidity, vinyl chloride film and solvent-based glue or cellophane tape, which can fade or discolor them. Keep the stopwatch away from magnetism, static electricity, strong vibration, dust and chemicals such as solvents, cosmetic sprays and detergents. Seiko gives the normal life of the liquid crystal panel as about 7 years.\u003c\/p\u003e","brand":"SEIKO","offers":[{"title":"Default Title","offer_id":47357721444515,"sku":"20260851","price":50000.0,"currency_code":"JPY","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0590\/1271\/0563\/files\/seiko-integrated-stopwatchprinter-system-gray-8253922.jpg?v=1771696994"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0590\/1271\/0563\/collections\/stopwatch-1819131.jpg?v=1771689668","url":"https:\/\/wafuu.com\/en-tr\/collections\/stopwatch.oembed","provider":"WAFUU JAPAN","version":"1.0","type":"link"}